Adaptation for Arm ETM Preprocessor Mictor

Order No.	Probe
LA-3308	Trace for Arm-ETM via AUTOFOCUS II (PACK)
LA-7921	Preprocessor for ARM-ETM 200 flex cable out of production
LA-7923	Preprocessor for ETM 2-MICTOR 2 flex cables out of production
LA-7991	Preprocessor for ARM-ETM with AUTOFOCUS Flex out of production
LA-7992	Preproc. for ARM-ETM/AUTOFOCUS II 600 Flex out of production

Tyco Part Number	Description
2-5767004-2	Vertical, surface mount, board to board/cable connector, RoHS compliant.
767054-1	Vertical, surface mount, board to board/cable connector.
767061-1	Vertical, surface mount, board to board/cable connector.
5767044-1	Right angle, straddle mount, board to board/cable connector, RoHS compliant.

Link to Tyco Electronics

The adaption uses one or two 38 pin Mictor connectors.
The second connector is only needed if the target trace port provides more than 16 trace data pins.
A separation distance of 1350 mil is required if adaption without flex cable is intended.
We recommend to place the even numbered pins at the PCB border side (flex cable won't be twisted).

Below you can see the pinout used for ETMv3/ETMv4/PFTv1 in Normal and Continuous mode for current Arm cores.
The pinouts for ETMv1 in Normal, Multiplexed and Demultiplexed mode for the older ARM7 and ARM9 cores are no
longer described here.

The pinout of the Mictor connector optionally includes the debug signals which needs to go to the Debug Cable
(20-pin standard header). The Preprocessors have a 20-pin connector where the user can plug in the Debug Cable.
Alternatively the Debug Cable can be plugged on a separate 20-pin connector on the target. In this case there is no
need to connect the debug signals to the Mictor. For better signal quality it is better not to connect them.
The debug signals are DBGRQ, RESET-, TDO, RTCK, TCK, TMS, TDI, TRST- DBGACK, VREF-DEBUG.

Connector 1

Signal	Pin			Pin	Signal
N/C	1			2	N/C
N/C	3			4	N/C
GND	5			6	TRACECLK
DBGRQ	7			8	DBGACK
RESET-	9			10	EXTRIG
TDO|-|SWO	11			12	VREF-TRACE
RTCK	13			14	VREF-DEBUG
TCK|TCKC|SWCLK	15			16	TRACEDATA[7]
TMS|TMSC|SWDIO	17			18	TRACEDATA[6]
TDI	19			20	TRACEDATA[5]
TRST-	21			22	TRACEDATA[4]
TRACEDATA[15]	23			24	TRACEDATA[3]
TRACEDATA[14]	25			26	TRACEDATA[2]
TRACEDATA[13]	27			28	TRACEDATA[1]
TRACEDATA[12]	29			30	GND
TRACEDATA[11]	31			32	GND
TRACEDATA[10]	33			34	VCC
TRACEDATA[9]	35			36	TRACECTL
TRACEDATA[8]	37			38	TRACEDATA[0]
Connect Pin 39,40,41,42,43 to GND

VCC needs to have VREF-TRACE level.

Connector 2 (only needed if more than 16 data bit)

Signal	Pin			Pin	Signal
N/C	1			2	N/C
N/C	3			4	N/C
GND	5			6	N/C
N/C	7			8	N/C
N/C	9			10	N/C
N/C	11			12	N/C
N/C	13			14	N/C
N/C	15			16	TRACEDATA[23]
N/C	17			18	TRACEDATA[22]
N/C	19			20	TRACEDATA[21]
N/C	21			22	TRACEDATA[20]
TRACEDATA[31]	23			24	TRACEDATA[19]
TRACEDATA[30]	25			26	TRACEDATA[18]
TRACEDATA[29]	27			28	TRACEDATA[17]
TRACEDATA[28]	29			30	GND
TRACEDATA[27]	31			32	GND
TRACEDATA[26]	33			34	VCC
TRACEDATA[25]	35			36	GND
TRACEDATA[24]	37			38	TRACEDATA[16]
Connect Pin 39,40,41,42,43 to GND

VCC needs to have VREF-TRACE level.