Arm CoreSight TPIU Target Adaptation via AutoFocus II MIPI

SAMTEC Part Number	Description
QSH-030-01-L-D-A	High Speed Ground Plane Socket

Link to SAMTEC

The adaption uses one 60 pin Samtec connector.
We recommend to place the odd numbered pins at the PCB border side (flex cable won't be twisted).

Signal	Pin			Pin	Signal
VREF-DEBUG	1			2	TMS|TMSC|SWDIO
TCK|TCKC|SWCLK	3			4	TDO|-|SWO
TDI	5			6	RESET-
RTCK	7			8	TRST- PULLDOWN
TRST-	9			10	DBGRQ TRIGIN
DBGACK TRIGOUT	11			12	VREF-TRACE
TRACECLK	13			14	GND
GND	15			16	GND
TRACECTL	17			18	TRACEDATA[19]
TRACEDATA[0]	19			20	TRACEDATA[20]
TRACEDATA[1]	21			22	TRACEDATA[21]
TRACEDATA[2]	23			24	TRACEDATA[22]
TRACEDATA[3]	25			26	TRACEDATA[23]
TRACEDATA[4]	27			28	TRACEDATA[24]
TRACEDATA[5]	29			30	TRACEDATA[25]
TRACEDATA[6]	31			32	TRACEDATA[26]
TRACEDATA[7]	33			34	TRACEDATA[27]
TRACEDATA[8]	35			36	TRACEDATA[28]
TRACEDATA[9]	37			38	TRACEDATA[29]
TRACEDATA[10]	39			40	TRACEDATA[30]
TRACEDATA[11]	41			42	TRACEDATA[31]
TRACEDATA[12]	43			44	GND
TRACEDATA[13]	45			46	GND
TRACEDATA[14]	47			48	GND
TRACEDATA[15]	49			50	GND
TRACEDATA[16]	51			52	GND
TRACEDATA[17]	53			54	GND
TRACEDATA[18]	55			56	GND
GND	57			58	GND
GND	59			60	GND
Connect metal plate to GND

If TRACECTL is not available ("continuous" mode) pin 17 shall be tied to GND.

The pinout of the Samtec MIPI-60 connector optionally includes the debug signals which needs to go to the CombiProbe
(34-pin MIPI header) or to the Debug Cable (20-pin standard header). The Preprocessors have a 34-pin MIPI connector
where the user can plug in the CombiProbe. Alternatively the CombiProbe (or Debug Cable) can be plugged on a
separate connector on the target. In this case there is no need to connect the debug signals to the MIPI-60. For better
signal quality it is better not to connect them. The debug signals are VREF-DEBUG, TCK, TDI, RTCK, TRST-,
DBGACK TRIGOUT, TMS, TDO, RESET-, TRST- PULLDOWN, DBGRQ TRIGIN.

Below you can see the pinout used for ETMv3/ETMv4/PFTv1 in Normal and Continuous mode for current Arm cores.
The pinouts for ETMv1 in Normal, Multiplexed and Demultiplexed mode for the older ARM7 and ARM9 cores are no
longer described here.

The adaptation applies to the following TRACE32 products:

Order No.	Probe
LA-3311	Trace for Arm-ETM via AUTOFOCUS II MIPI(PACK)
LA-3331	Trace for C6000 via AUTOFOCUS II MIPI (PACK)
LA-3345	Trace for C7000 via AutoFocus II MIPI (PACK)
LA-3916	Preproc. for C6000 AUTOFOCUS II MIPI60 out of production
LA-3925	Preproc. for C7000 DSP AUTOFOCUS II MIPI60 out of production
LA-7993	Preproc. for ARM-ETM/AUTOFOCUS 600 MIPI out of production

Lauterbach offers converters for adapting to target connectors that differ from the above-shown pinout.