|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | |  | | |
| GND | 1 |  |  | 2 | GND |
| PETP[0] | 3 | | | 4 | PERP[0] |
| PETN[0] | 5 | | | 6 | PERN[0] |
| GND | 7 | | | 8 | GND |
| PETP[1] | 9 | | | 10 | PERP[1] |
| PETN[1] | 11 | | | 12 | PERN[1] |
| GND | 13 | | | 14 | GND |
| PETP[2] | 15 | | | 16 | PERP[2] |
| PETN[2] | 17 | | | 18 | PERN[2] |
| GND | 19 | | | 20 | GND |
| PETP[3] | 21 | | | 22 | PERP[3] |
| PETN[3] | 23 | | | 24 | PERN[3] |
| GND | 25 | | | 26 | GND |
| PETP[4] | 27 | | | 28 | PERP[4] |
| PETN[4] | 29 | | | 30 | PERN[4] |
| GND | 31 | | | 32 | GND |
| PETP[5] | 33 | | | 34 | PERP[5] |
| PETN[5] | 35 | | | 36 | PERN[5] |
| GND | 37 | | | 38 | GND |
| PETP[6] | 39 | | | 40 | PERP[6] |
| PETN[6] | 41 | | | 42 | PERN[6] |
| GND | 43 | | | 44 | GND |
| PETP[7] | 45 | | | 46 | PERP[7] |
| PETN[7] | 47 | | | 48 | PERN[7] |
| GND | 49 | | | 50 | GND |
| WAKE# | 51 | | | 52 | REFCLK+ |
| PWRGOOD | 53 | | | 54 | REFCLK- |
| GND | 55 | | | 56 | GND |
| RESERVED | 57 | | | 58 | RESERVED |
| RESERVED | 59 | | | 60 | RESERVED |
| VCC3V3 | 61 | | | 62 | VCC3V3 |
| RESERVED | 63 | | | 64 | RESERVED |
| RESERVED | 65 | | | 66 | RESERVED |
| VCC3V3 | 67 | | | 68 | VCC3V3 |
| RESERVED | 69 | | | 70 | GND |
| RESERVED | 71 | | | 72 | RESERVED |
| VCC3V3 | 73 | | | 74 | VCC3V3 |
| RESERVED | 75 | | | 76 | RESERVED |
| RESERVED | 77 | | | 78 | VCCSENSE |
| VCC3V3 | 79 | | | 80 | VCC3V3 |
| | |  | | |
| Target connector, top-view, connect the two latch pins to GND |
 Signals
PETP/PETN, PERP/PERN: PCIe Transmitter/Receiver Positiv/Negative.
AC-coupling (220nF) already done on tool side, no caps required on target side.
REFCLK+, REFCLK-: The PCIe Reference Clock must be driven by the root complex (target).
VCCSENSE is optional and indicates the voltage level of WAKE# and PWRGOOD which normally needs to be 3.3V.
RESERVED must be left unconnected, because they are connected on tool side for a purpose not needed here.
Pin 70 must be driven GND. It is used to detect if a target is connected and activates voltage at VCC3V3.
VCC3V3: 3.3V power sourced by the tool. It can be used to supply pull-up resistors for the WAKE# and PWRGOOD signals if needed.
Do not connect otherwise.
Cable for Connection to Target
| Order-Nr. | Type |
| LA-1239 | 500 mm flex extension for PowerTrace Serial |
| LA-1211 | 500 mm flex extension for PowerTrace Serial advanced speed grade |
| LA-3522 | Accessories for PTSerial for ARM-ETM 7-8Lanes |
Target Connector Type
| Pins | Samtec Order No | Connector Type | Samtec ASP Nr. |
| 80 | ERF8-040-05.0-S-DV-L | Rugged High Speed Socket 80 pin | ASP-148424-01 |
 SAMTEC connector data sheet
|
| Order No. | Probe |
|---|
| LA-3310 | Trace for Arm-ETM via PT-Serial 4GB (PACK) |
| LA-3320 | Trace for Arm-ETM via PT-Serial 8GB (PACK) |
| LA-3328 | Trace for QorIQ PowerPC via PTS 4GB (PACK) |
| LA-3329 | Trace for QorIQ PowerPC via PTS 8GB (PACK) |
Lauterbach offers converters for adapting to target connectors that differ from the above-shown pinout.
PTSERIAL-PCIe-Gen3 x4 Slot-Card-Adapter PTSERIAL-PCIe-Gen3 x8 Slot-Card-Adapter PTSERIAL-MiniPCIe-Gen3 x1 Slot-Card-Adapter PTSERIAL-PCIe-Gen3 x1 Slot-Card-Adapter PCIe Gen 4 Preprocessor for PowerTrace Serial Accessories for PTSerial MiniPCIe x1
out of production Accessories for PTSerial PCIe x4 Slot-Card
out of production OCuLink Trace Adapter for PowerTrace Serial
|
