 PPC603X - PPC750 - MPC5200 - MPC512X - MPC74XX - MPC82XX - MPC83XX - MPC86XX
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | |  | | |
| TDO | 1 |  |  | 2 | (QACK-) |
| TDI | 3 | | | 4 | TRST- |
| (QREQ-) | 5 | | | 6 | JTAG-VREF |
| TCK | 7 | | | 8 | (PRESENT-) |
| TMS | 9 | | | 10 | N/C |
| (SRESET-) | 11 | | | 12 | GND |
| HRESET- | 13 | | | 14 | N/C (KEY PIN) |
| (CKSTOP-) | 15 | | | 16 | GND |
| | |  | | |
MPC85XX (PQ3), QorIQ P10XX and P20XX
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | | | | |
| TDO | 1 | | | 2 | N/C |
| TDI | 3 | | | 4 | TRST- |
| (RUNSTOP-) | 5 | | | 6 | JTAG-VREF |
| TCK | 7 | | | 8 | (CHKSTPIN-) |
| TMS | 9 | | | 10 | N/C |
| (SRESET-) | 11 | | | 12 | GND |
| HRESET- | 13 | | | 14 | N/C (KEY PIN) |
| (CKSTOPOUT-) | 15 | | | 16 | GND |
| | | | | |
QorIQ PowerPC 32/64 Bit
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | | | | |
| TDO | 1 | | | 2 | N/C |
| TDI | 3 | | | 4 | TRST- |
| (RUNSTOP-) | 5 | | | 6 | JTAG-VREF |
| TCK | 7 | | | 8 | (CHKSTPIN-) |
| TMS | 9 | | | 10 | N/C |
| (SRESET-) | 11 | | | 12 | GND |
| PORESET- | 13 | | | 14 | N/C (KEY PIN) |
| (CKSTOPOUT-) | 15 | | | 16 | GND |
| | | | | |
Signals
- Pin 6 (JTAG-VREF) must match the JTAG I/O voltage of the processor. JTAG-VREF should have a resistance less than 5kOhm for 3.0~5.0V, less than 2kOhm for 1.8~3.0V.
- Pin 8 will, by default, be permanently driven to JTAG-VTREF level by the debugger.
- Signals in brackets are not necessary for debugging, but it is recommended to connect those signals if available.
- Signals which are not available should be left unconnected on the debug connector.
Target Connector Type
- This is a standard 16 pin double row (two rows of 8 pins) connector (pin to pin spacing: 2.54mm/0.100").
- If terminal strip without shroud is used, the spacing marked with "A" must be a minimum of 25.5mm/1".
- Examples with housing: Samtec HTST-108-01-L-D (through-hole); Samtec HTST-108-01-L-DV (surface mount).
The adaptation applies to the following TRACE32 products:
| Order No. | Probe |
|---|
| LA-3735 | JTAG Debugger for MPC86xx (ICD) |
| LA-3794 | JTAG Debugger for QorIQ PowerPC 64-Bit (ICD) |
| LA-3795 | JTAG Debugger QorIQ PowerPC 32-Bit (ICD) |
| LA-3796 | JTAG Debugger for MPC85XX/QorIQ e500 (ICD) |
| LA-7719 | JTAG Debugger for MPC74xx (ICD) |
| LA-7721 | JTAG Debugger for PPC603/MPC74x/75x (ICD) |
| LA-7729 | JTAG Debugger for MPC82xx/MPC83xx(ICD) |
| LA-7734 | JTAG Debugger for MPC5200/MPC512x (ICD) |
Lauterbach offers converters for adapting to target connectors that differ from the above-shown pinout.
Conv. Samtec40/COP16 to Samtec70 PowerOrg Conv. Samtec40/COP16 to Samtec46 PowerOrg Conv. Samtec40/COP16 to Samtec22 PowerOrg
|
Pinout
