Target Pinout Specification for PowerPC-COP |
 
|
|||||||
|
||||||||
| ||||||||
Pinout
|
 |
 |
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Signal | Pin | Pin | Signal | ||
|---|---|---|---|---|---|
 | |||||
| TDO | 1 |  |  | 2 | (QACK-) |
| TDI | 3 | | | 4 | TRST- |
| (QREQ-) | 5 | | | 6 | JTAG-VREF |
| TCK | 7 | | | 8 | (PRESENT-) |
| TMS | 9 | | | 10 | N/C |
| (SRESET-) | 11 | | | 12 | GND |
| HRESET- | 13 | | | 14 | N/C (KEY PIN) |
| (CKSTOP-) | 15 | | | 16 | GND |
 | |||||
MPC512X - MPC5200 - MPC82XX - MPC83XX - MPC85XX - MPC86XX - QorIQ P10XX and P20XX
| Signal | Pin | Pin | Signal | ||
|---|---|---|---|---|---|
| |||||
| TDO | 1 | | | 2 | N/C |
| TDI | 3 | | | 4 | TRST- |
| (RUNSTOP-) | 5 | | | 6 | JTAG-VREF |
| TCK | 7 | | | 8 | (CHKSTPIN-) |
| TMS | 9 | | | 10 | N/C |
| (SRESET-) | 11 | | | 12 | GND |
| HRESET- | 13 | | | 14 | N/C (KEY PIN) |
| (CKSTOPOUT-) | 15 | | | 16 | GND |
| |||||
QorIQ PowerPC 32/64 Bit
| Signal | Pin | Pin | Signal | ||
|---|---|---|---|---|---|
| |||||
| TDO | 1 | | | 2 | N/C |
| TDI | 3 | | | 4 | TRST- |
| (RUNSTOP-) | 5 | | | 6 | JTAG-VREF |
| TCK | 7 | | | 8 | (CHKSTPIN-) |
| TMS | 9 | | | 10 | N/C |
| (SRESET-) | 11 | | | 12 | GND |
| PORESET- | 13 | | | 14 | N/C (KEY PIN) |
| (CKSTOPOUT-) | 15 | | | 16 | GND |
| |||||
Signals
- Pin 6 (JTAG-VREF) must match the JTAG I/O voltage of the processor. JTAG-VREF should have a resistance less than 5kOhm for 3.0~5.0V, less than 2kOhm for 1.8~3.0V.
- Pin 8 will, by default, be permanently driven to JTAG-VTREF level by the debugger.
- Signals in brackets are not necessary for debugging, but it is recommended to connect those signals if available.
- Signals which are not available should be left unconnected on the debug connector.
Target Connector Type
- This is a standard 16 pin double row (two rows of 8 pins) connector (pin to pin spacing: 2.54mm/0.100").
- If terminal strip without shroud is used, the spacing marked with "A" must be a minimum of 25.5mm/1".
- Examples with housing: Samtec HTST-108-01-L-D (through-hole); Samtec HTST-108-01-L-DV (surface mount).
The adaptation applies to the following TRACE32 products:
| Order No. | Probe |
|---|---|
| LA-3290 | PPCCOP Debug Probe with MPC74xx License new product |
| LA-3291 | PPCCOP Debug Probe with PPC603 License new product |
| LA-3292 | PPCCOP Debug Probe with MPC82xx/MPC83xx Lic. new product |
| LA-3293 | PPCCOP Debug Probe with MPC51xx/MPC52xx Lic. new product |
| LA-3294 | PPCCOP Debug Probe with QorIQ 64-Bit License new product |
| LA-3295 | PPCCOP Debug Probe with QorIQ 32-Bit License new product |
| LA-3296 | PPCCOP Dbg.Probe with MPC85XX/QorIQ-e500 Lic. new product |
| LA-3297 | PPCCOP Debug Probe with MPC86xx License new product |
| LA-3735 | JTAG Debugger for MPC86xx (ICD) out of production |
| LA-3794 | JTAG Debugger for QorIQ PowerPC 64-Bit (ICD) out of production |
| LA-3795 | JTAG Debugger QorIQ PowerPC 32-Bit (ICD) out of production |
| LA-3796 | JTAG Debugger for MPC85XX/QorIQ e500 (ICD) out of production |
| LA-7719 | JTAG Debugger for MPC74xx (ICD) out of production |
| LA-7721 | JTAG Debugger for PPC603/MPC74x/75x (ICD) out of production |
| LA-7729 | JTAG Debugger for MPC82xx/MPC83xx(ICD) out of production |
| LA-7734 | JTAG Debugger for MPC5200/MPC512x (ICD) out of production |
Lauterbach offers converters for adapting to target connectors that differ from the above-shown pinout.
Picture
Order No.
Probe
|
Copyright © 2026 Lauterbach GmbH, Altlaufstr.40, 85635 Höhenkirchen-Siegertsbrunn, Germany
Impressum
Privacy Policy
The information presented is intended to give overview information only. Changes and technical enhancements or modifications can be made without notice. Report Errors Last generated/modified: 18-Aug-2026 |
