Target Adaptation for C6000 Trace

The adaptation applies for the following TRACE32 products:

Order No.	Probe
LA-3330	Trace for C6000 via AUTOFOCUS II (PACK)
LA-3331	Trace for C6000 via AUTOFOCUS II MIPI (PACK)
LA-3903	Preproc. for C6000 DSP AF II Mictor38 Flex out of production
LA-3916	Preproc. for C6000 AUTOFOCUS II MIPI60 out of production

SAMTEC Part Number	Description
QSH-030-01-L-D-A	High Speed Ground Plane Socket

Link to SAMTEC

The adaptation uses one 60 pin Samtec connector. We recommend to place the odd numbered pins at the PCB border side (flex cable won't be twisted).

Signal	Pin			Pin	Signal
VREF-DEBUG	1			2	TMS|TMSC|SWDIO
TCK|TCKC|SWCLK	3			4	TDO|-|SWO
TDI	5			6	RESET-
RTCK	7			8	TRST- PULLDOWN
TRST-	9			10	DBGRQ TRIGIN
DBGACK TRIGOUT	11			12	VREF-TRACE
TRACECLK	13			14	GND
GND	15			16	GND
TRACECTL	17			18	TRACEDATA[19]
TRACEDATA[0]	19			20	TRACEDATA[20]
TRACEDATA[1]	21			22	TRACEDATA[21]
TRACEDATA[2]	23			24	TRACEDATA[22]
TRACEDATA[3]	25			26	TRACEDATA[23]
TRACEDATA[4]	27			28	TRACEDATA[24]
TRACEDATA[5]	29			30	TRACEDATA[25]
TRACEDATA[6]	31			32	TRACEDATA[26]
TRACEDATA[7]	33			34	TRACEDATA[27]
TRACEDATA[8]	35			36	TRACEDATA[28]
TRACEDATA[9]	37			38	TRACEDATA[29]
TRACEDATA[10]	39			40	TRACEDATA[30]
TRACEDATA[11]	41			42	TRACEDATA[31]
TRACEDATA[12]	43			44	GND
TRACEDATA[13]	45			46	GND
TRACEDATA[14]	47			48	GND
TRACEDATA[15]	49			50	GND
TRACEDATA[16]	51			52	GND
TRACEDATA[17]	53			54	GND
TRACEDATA[18]	55			56	GND
GND	57			58	GND
GND	59			60	GND
Connect metal plate to GND

If TRACECTL is not available ("continuous" mode) pin 17 shall be tied to GND.

Tyco Part Number	Description
2-5767004-2	Vertical, surface mount, board to board/cable connector, RoHS compliant.
767054-1	Vertical, surface mount, board to board/cable connector.
767061-1	Vertical, surface mount, board to board/cable connector.
5767044-1	Right angle, straddle mount, board to board/cable connector, RoHS compliant.

Link to Tyco Electronics

The adaptation uses one or two 38 pin Mictor connectors.
The second connector is only needed if the target trace port provides more than 16 trace data pins and for 8/16 bit demuxed mode.
A separation distance of 1350 mil is required if adaption without flex cable is intended.
We recommend to place the even numbered pins at the PCB border side (flex cable won't be twisted).

Connector "TRACE A"

Signal	Pin			Pin	Signal
N/C	1			2	N/C
N/C	3			4	N/C
GND	5			6	TRACECLK
DBGRQ	7			8	DBGACK
RESET-	9			10	EXTRIG
TDO|-|SWO	11			12	VREF-TRACE
RTCK	13			14	VREF-DEBUG
TCK|TCKC|SWCLK	15			16	TRACEDATA[7]
TMS|TMSC|SWDIO	17			18	TRACEDATA[6]
TDI	19			20	TRACEDATA[5]
TRST-	21			22	TRACEDATA[4]
TRACEDATA[15]	23			24	TRACEDATA[3]
TRACEDATA[14]	25			26	TRACEDATA[2]
TRACEDATA[13]	27			28	TRACEDATA[1]
TRACEDATA[12]	29			30	GND
TRACEDATA[11]	31			32	GND
TRACEDATA[10]	33			34	VCC
TRACEDATA[9]	35			36	TRACECTL
TRACEDATA[8]	37			38	TRACEDATA[0]
Connect Pin 39,40,41,42,43 to GND

VCC needs to have VREF-TRACE level.

Connector "TRACE B" (only needed if more than 16 data bit)

Signal	Pin			Pin	Signal
N/C	1			2	N/C
N/C	3			4	N/C
GND	5			6	N/C
N/C	7			8	N/C
N/C	9			10	N/C
N/C	11			12	N/C
N/C	13			14	N/C
N/C	15			16	TRACEDATA[23]
N/C	17			18	TRACEDATA[22]
N/C	19			20	TRACEDATA[21]
N/C	21			22	TRACEDATA[20]
TRACEDATA[31]	23			24	TRACEDATA[19]
TRACEDATA[30]	25			26	TRACEDATA[18]
TRACEDATA[29]	27			28	TRACEDATA[17]
TRACEDATA[28]	29			30	GND
TRACEDATA[27]	31			32	GND
TRACEDATA[26]	33			34	VCC
TRACEDATA[25]	35			36	GND
TRACEDATA[24]	37			38	TRACEDATA[16]
Connect Pin 39,40,41,42,43 to GND

VCC needs to have VREF-TRACE level.

This connector can be found on many TI boards.

Lauterbach provides the following converters to the CTOOLS60 pinout.